現在A(yíng)ndroid版本更新太快，2.1是最普遍的版本，不過馬上都開始升級2.2版本了，目前網路上提供了很多自制作的andorid ROM，通過刷機工具進行刷機，最普遍的是利用android的recovery機制進行update，現將recovery的
內部工作原理摘錄如下
/*
* The recovery tool communicates with the main system through /cache files.
* /cache/recovery/command - INPUT - command line for tool, one arg per line
* /cache/recovery/log - OUTPUT - combined log file from recovery run(s)
* /cache/recovery/intent - OUTPUT - intent that was passed in
*
* The arguments which may be supplied in the recovery.command file:
* --send_intent=anystring - write the text out to recovery.intent
* --update_package=root:path - verify install an OTA package file
* --wipe_data - erase user data (and cache), then reboot
* --wipe_cache - wipe cache (but not user data), then reboot
* --set_encrypted_filesystem=on|off - enables / diasables encrypted fs
*
* After completing, we remove /cache/recovery/command and reboot.
* Arguments may also be supplied in the bootloader control block (BCB).
* These important scenarios must be safely restartable at any point:
*
* FACTORY RESET
* 1. user selects "factory reset"
* 2. main system writes "--wipe_data" to /cache/recovery/command
* 3. main system reboots into recovery
* 4. get_args() writes BCB with "boot-recovery" and "--wipe_data"
* -- after this, rebooting will restart the erase --
* 5. erase_root() reformats /data
* 6. erase_root() reformats /cache
* 7. finish_recovery() erases BCB
* -- after this, rebooting will restart the main system --
* 8. main() calls reboot() to boot main system
*
* OTA INSTALL
* 1. main system downloads OTA package to /cache/some-filename.zip
* 2. main system writes "--update_package=CACHE:some-filename.zip"
* 3. main system reboots into recovery
* 4. get_args() writes BCB with "boot-recovery" and "--update_package=..."
* -- after this, rebooting will attempt to reinstall the update --
* 5. install_package() attempts to install the update
* NOTE: the package install must itself be restartable from any point
* 6. finish_recovery() erases BCB
* -- after this, rebooting will (try to) restart the main system --
* 7. ** if install failed **
* 7a. prompt_and_wait() shows an error icon and waits for the user
* 7b; the user reboots (pulling the battery, etc) into the main system
* 8. main() calls maybe_install_firmware_update()
* ** if the update contained radio/hboot firmware **:
* 8a. m_i_f_u() writes BCB with "boot-recovery" and "--wipe_cache"
* -- after this, rebooting will reformat cache & restart main system --
* 8b. m_i_f_u() writes firmware image into raw cache partition
* 8c. m_i_f_u() writes BCB with "update-radio/hboot" and "--wipe_cache"
* -- after this, rebooting will attempt to reinstall firmware --
* 8d. bootloader tries to flash firmware
* 8e. bootloader writes BCB with "boot-recovery" (keeping "--wipe_cache")
* -- after this, rebooting will reformat cache & restart main system --
* 8f. erase_root() reformats /cache
* 8g. finish_recovery() erases BCB
* -- after this, rebooting will (try to) restart the main system --
* 9. main() calls reboot() to boot main system
*
* ENCRYPTED FILE SYSTEMS ENABLE/DISABLE
* 1. user selects "enable encrypted file systems"
* 2. main system writes "--set_encrypted_filesystem=on|off" to
* /cache/recovery/command
* 3. main system reboots into recovery
* 4. get_args() writes BCB with "boot-recovery" and
* "--set_encrypted_filesystems=on|off"
* -- after this, rebooting will restart the transition --
* 5. read_encrypted_fs_info() retrieves encrypted file systems settings from /data
* Settings include: property to specify the Encrypted FS istatus and
* FS encryption key if enabled (not yet implemented)
* 6. erase_root() reformats /data
* 7. erase_root() reformats /cache
* 8. restore_encrypted_fs_info() writes required encrypted file systems settings to /data
* Settings include: property to specify the Encrypted FS status and
* FS encryption key if enabled (not yet implemented)
* 9. finish_recovery() erases BCB
* -- after this, rebooting will restart the main system --
* 10. main() calls reboot() to boot main system
*/
聯系客服
